基于热电效应的高效环控系统

部分空间科学实验对环境温度有较高的要求，环境温度高于或低于空间科学系统能够提供的热沉温度，需要有可靠有效的加温降温处理措施。使用可靠性强的热电制冷片作为制冷制热方式和气液换热器二次换热来实现环境温度控制的需求，并对不同流体温度制冷制热效果进行分析，结果表明流体温度和目标温度差越小，热电制冷制热的效果越好。在环境温度制冷工况中，热电单元数量随电流增加先减少后增加，在制热工况中则单调递减，设计中需按照制冷工况进行热电单元数量的确定。当流体温度接近制冷制热的目标温度时，会出现整个系统总效率优于热电系统效率的区间。通过对热电单元和气液换热器的组合系统的性能计算，提供一种适于热电环控系统的计算方法和部件选型思路，对空间站环控系统的设计有重要参考意义。     

PAN纤维共聚单体作用机理的光电离质谱研究

本工作以丙烯腈/衣康酸（IA）二元共聚原丝以及丙烯腈/IA/丙烯酸甲酯（MA）三元共聚原丝为研究对象，利用热重分析仪（TG）和热解-同步辐射真空紫外光电离质谱（Py-SVUV-PIMS）对其热稳定化过程进行研究。TG结果表明，氮气气氛下，二元共聚原丝（PAN/IA）和三元共聚原丝（PAN/IA/MA）分别呈现三阶段和两阶段的热分解过程，其中PAN/IA的第一和第二阶段均对应PAN线型分子链的断裂，但前者是由自由基环化反应放热引发的，后者则是由正常温度下的热分解所致，而单体MA的加入显著抑制了自由基环化反应，使得PAN原丝的热稳定化能够以单体IA诱导的离子型环化反应为主较平缓地进行，相应的热失重过程也由两阶段转变为了单阶段。Py-SVUV-MS的实验结果表明，两种共聚PAN原丝在程序升温过程中会生成包括含氮小分子、丙烯腈单体及低聚物、成环化合物在内的三类主要热解产物，对比各类产物的生成趋势和产量，推断单体MA通过降低PAN结构的规整度，使其无定形化，从而增加环化反应的引发点，促进PAN原丝向稳定的预氧丝转变，同时由典型热解产物——甲基丙烯腈的生成路径可知，MA本身并不参与PAN大分子的环化反应，属于中性共聚单体。空气气氛下，CO₂的产量差异也间接证明了MA单体能够有效提升PAN纤维的固碳能力，采用三元共聚方法制得的PAN纤维热稳定性能更佳。     

酸性废水中As(Ⅲ)、Cu(Ⅱ)与铁粉的反应行为

在Fe-As(Ⅲ)-Cu(Ⅱ)-H₂O体系中, 研究了酸性废水中As(Ⅲ)、Cu(Ⅱ)与金属铁粉的反应行为, 考察了反应过程中As在气、液、固三相中的分配比。结果表明, As(Ⅲ)和Cu(Ⅱ)离子被Fe还原为单质As和Cu后, As、Cu进一步结合成Cu₅As₂等金属间化合物, 从而促进As(Ⅲ)沉淀反应的发生, 且无AsH3生成。在反应时间40min、铁粉过量系数1.2、溶液初始pH=0.0、温度40 ℃、Cu/As摩尔比1.0条件下, As在气、液、固三相中的分配比分别为0、20.7%和79.3%, 沉砷率为79.3%。     

Temperature cycling and its effect on mechanical behaviours of highporosity chalks

Temperature history can have a significant effect on the strength of water-saturated chalk.In this study,hydrostatic stress cycles are applied to understand the mechanical response of chalk samples exposed to temperature cycling between each stress cycle,compared to the samples tested at a constant temperature.The total accumulated strain during a stress cycle and the irreversible strain are reported.Chalk samples from Kansas(USA)and Mons(Belgium),with different degrees of induration(i.e.amount of contact cementation),were used.The samples were saturated with equilibrated water(polar)and nonpolar Isopar H oil to quantify water weakening.All samples tested during 10 stress cycles with varying temperature(i.e.temperature cycled in between each stress cycle)accumulated more strain than those tested at constant temperatures.All the stress cycles were performed at 30℃.The two chalk types behaved similarly when saturated with Isopar H oil,but differently when saturated with water.When saturated with water,the stronger Kansas chalk accumulated more total strain and more irreversible strain within each stress cycle than the weaker Mons chalk.     

基于热负荷自动调节的延迟焦化加热炉三点注汽量智能优化

针对国内某炼油厂延迟焦化加热炉三点注汽问题，采用热负荷自动调节的算法进行了研究。运用该模型方法，分析了三点注汽量对加热炉热负荷和炉管结焦系数的影响，发现三点注汽量的改变均会对热负荷和炉管结焦系数产生影响，主要表现为提高注汽量将会提高热负荷，同时降低结焦系数；第1点注汽量和第2点注汽量对热负荷和结焦系数的影响较强，第3点注汽量对热负荷和结焦系数的影响较弱。在实际操作中，加热炉中的结焦程度既不能太强也不能太弱，合适的结焦系数能够保证正常开工周期里炉管不结焦，也能保证瓦斯、注汽量等参数的合理分配。通过对热负荷、注汽量的智能分配，可得到不同原料油加工负荷条件下更加合理的装置运行方案。     

餐厨污水就地处理与中水回用工艺的探索与实践

以无锡某厂食堂污水处理及中水回用为例,探讨采用"隔油+混凝沉淀+A^2/O+MBR"工艺就地处理餐厨污水,并将出水回用于厂区冲厕可行性。经过78 d的调试,该工艺实现了餐厨污水中污染物的去除,COD小于50mg/L,NH4^+-N质量浓度小于5 mg/L,总氮小于10 mg/L,总磷小于0.5 mg/L,大肠杆菌数小于2个/L,基本满足中水回用要求。经计算吨水处理成本9.83元,含电费、药剂费、人工费、污泥处理费及膜更换费用。结合中水回用节省自来水后计算吨水处理综合成本为5.23元,大幅降低公司对市政供水的依赖,降低公司用水成本。     

汽车发动机用AZ91D合金的表面喷涂与性能

采用热喷涂工艺在压铸态AZ91D合金表面制备了Al涂层,研究了热处理温度和保温时间对AZ91/Al涂层界面组织形貌的影响,并对比分析了扩散层的耐腐蚀性能和耐磨性能。结果表明,热处理前Al涂层与基材为机械结合,热处理后Al涂层与AZ91合金基材的界面处可形成冶金结合扩散层,且随着保温时间延长,扩散层厚度不断增加;热处理温度在375 ℃以下时扩散层主要由β-Mg₁₇Al₁₂相构成,375 ℃×8 h热处理后为α-Mg+β-Mg₁₇Al₁₂相,425 ℃×1 h热处理后为γ-Mg₂Al₃和β-Mg₁₇Al₁₂相。AZ91合金基材和扩散层腐蚀电位从高至低顺序为γ>β>α+β>AZ91合金基材,扩散层的腐蚀电流密度均低于AZ91合金基材,阻抗谱图中容抗弧半径从大至小顺序为γ>β>α+β>AZ91合金基材,扩散层的耐腐蚀性能均优于AZ91合金基材;γ、β和α+β扩散层的摩擦稳定性系数都高于AZ91合金基材,而磨损速率和磨痕宽度都要小于AZ91合金基材,其中β扩散层的磨损速率和磨痕宽度最小,具有最佳的抵抗磨损的能力。     

可持续煤矿矿井水处理与资源化技术综述

煤矿开采过程中会产生大量的废弃矿井水,不仅造成水资源的大量浪费,而且还威胁着矿区生态环境。本文综述了我国常见矿井水的常规处理方法,以及将矿井水视为水资源的可持续矿井水水处理与资源化技术,首次提出以“时间维度和空间维度”对矿井水进行全时空处理,并着重阐述了矿井水分级处理、分质利用技术,反渗透浓水处理与资源化技术,煤泥处理与资源化技术,以及重金属回收与利用技术等,对煤矿区矿井水处理与资源化利用具有指导意义。     

Suitability,efficiency and microbiological safety of novel physical technologies for the processing of ready‐to‐eat meals,meats and pumpable products

Consumer studies and market reports show an increase in consumption of ready‐to‐eat (RTE) foods. Although conventional processing technologies can in most cases produce safe products, they can also lead to the degradation of nutritional compounds and negatively affect quality characteristics. Consumers strongly prefer food that is minimally processed with the maximum amount of health‐promoting substances. Novel processing technologies as pre‐ or post‐treatment decontamination methods or as substitutes of conventional technologies have the potential to produce foods that are safe, rich in nutrient content and with superior organoleptic properties. Combining novel with conventional processes can eliminate potential drawbacks of novel technologies. This review examines available scientific information and critically evaluates the suitability and efficiency of various novel thermal and nonthermal technologies in terms of microbial safety, quality as well as nutrient content on the production of RTE meals, meats and pumpable products.     

Study of Compatibilized Liquid Crystalline Polymer/Cyclic Olefin Copolymer Blends

The technology to produce compatibilized blends of liquid crystalline polymer and highly amorphous cyclic olefin copolymers through two novel approaches were studied. The first approach was to use silane-functionalized halloysite nanotube as nonspecific compatibilizer and the second method was reactive compatibilization. The study of blends and their resulting microstructure; their thermal, mechanical, and viscoelastic properties were investigated. The kinetic study of blends compatibilized through both routes was performed.